9VJL3 Intel Socket 478 VIA P4X400 + VT8235 ATX Motherboard User`s

of 16

Please download to get full document.

View again

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
PDF
16 pages
2 downs
231 views
Share
Description
Declaration of Conformity According to 47 CFR, Parts 2 and 15 of the FCC Rules 9VJL3 The following designated product: EQUIPMENT: Intel Socket 478 VIA P4X400 +…
Transcript
Declaration of Conformity According to 47 CFR, Parts 2 and 15 of the FCC Rules 9VJL3 The following designated product: EQUIPMENT: Intel Socket 478 VIA P4X400 + VT8235 ATX Motherboard MAINBOARD MODEL NO.: 9VJL3 is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. User’s Guide This declaration is given to the manufacturer: CHAINTECH-EXCEL COMPUTER INC. 4427 Enterprise St. Fremont, CA 94538, U.S.A. http://www.chaintech-excel.com Chaintech President: Version 1.0 Signature: Simon Ho Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: * This device may not cause harmful interference. * This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to TABLE OF CONTENTS Chapter 1 Introduction ...............................................................1 1-1 Product Specifications..................................................................................... 1 Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 1-2 Package Contents ............................................................................................ 2 in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this 1-3 9VJL3 Motherboard Diagram ......................................................................... 3 equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful 1-4 9VJL3 Motherboard Layout............................................................................ 4 interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can Chapter 2 Hardware Setup.........................................................5 be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one 2-1 Installing a CPU Processor for Socket 478 ..................................................... 5 or more of the following measures: 2-2 Setting Your CPU’s Performance.................................................................... 5 * Reorient or relocate the receiving antenna. 2-3 Main Memory Configuration .......................................................................... 6 * Increase the separation between the equipment and receiver. 2-4 Connector and Jumper Reference Chart ......................................................... 6 * Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 2-5 Connector and Jumper Settings....................................................................... 7 * Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure Chapter 3 BIOS Setup Program ..............................................12 compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party 3-1 Standard CMOS Setup .................................................................................. 12 responsible for compliance could void the user's authority to operate this equipment. 3-2 Advanced BIOS Features .............................................................................. 13 Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for audio noise emissions from digital apparatuses 3-3 Advanced Chipset Features........................................................................... 15 3-4 Integrated Peripherals.................................................................................... 17 set out in the Radio Interference Regulations of the Canadian Department of Communications. 3-5 Power Management Setup............................................................................. 20 Manufacturer's Disclaimer Statement 3-6 PNP/PCI Configurations ............................................................................... 22 The information in this document is subject to change without notice and does not represent a commitment 3-7 Frequency/Voltage Control ........................................................................... 23 on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the 3-8 Load Fail-Safe Defaults ................................................................................ 24 quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to 3-9 Load Optimized Defaults .............................................................................. 24 make changes to the content of this document and/or the products associated with it at any time without obligation 3-10 Supervisor Password & User Password Setting .................................................. 24 to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect, 3-11 Save and Exit Setup..................................................................................... 24 special, incidental or consequential damages arising out of the use or inability to use this product or documentation, 3-12 Exit Without Saving .................................................................................... 24 even if advised of the possibility of such damages. This document contains materials protected by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted in any form, by any means or for any Chapter 4 DRIVER Setup ........................................................25 purpose without expressed written consent of its authors. Product names appearing in this document are mentioned 4-1 VIA Service Pack Setup................................................................................ 25 for identification purposes only. All trademarks, product names or brand names appearing in this document are 4-2 Audio Driver Setup ....................................................................................... 25 registered property of their respective owners. 4-3 LAN Driver Setup ......................................................................................... 26 4-4 USB 2.0 Driver.............................................................................................. 26 Printed in Taiwan. 100% Jan 2003 OST-CONSUMER RECYCLED PAPER How To Contact CHAINTECH .............................................28 Chapter 1 Chapter 1 Boot-Block Flash ROM Chapter 1 Introduction - 1-1 Product Specifications Award system BIOS supports PnP, APM, DMI, ACPI, & Multi-device booting features. Processor - Supports Intel Celeron/Pentium 4 Socket 478 CPU - Supports Intel Celeron/Pentium 4 system bus at 400/533MHz 1-2 Package Contents This product comes with the following components: Chipset - VIA P4X400 + VT8235 Main Memory - Supports two 184 pin DDR DIMMs up to 2GB - Supports PC 1600/2100/2700 DDR SDRAM modules One AGP slot for 4X/8X AGP - Five 32-Bit PCI slots (v2.2 compatible) With external high quality AC’97 Codec - Complete software driver supports for Windows® OS Ultra DMA 66/100/133 PCI IDE Controller - Supports two IDE ports up to 4 ATAPI devices - Supports PIO Mode 4 up to 16.6MBps, Multi Mode 4 up to 66MBps, Multi Word Mode 5 up to 100MBps and Multi Word Mode 6 up to 133MBps with Bus Mastering - Bus-Mastering software drivers for all common multi-tasking operating systems USB 2.0/1.0 Host Controller - Three EHCI USB 2.0 controllers support total six USB 2.0/1.1 ports - Supports USB 2.0 high-speed device @480 Mb/s transfer rates On board ITE 8700 Super I/O Functions - Two UARTs support serial port and IR function (up to 115.2Kbps) for HPSIR and - One SPP/ECP/EPP parallel port - One floppy disk drive connector supports up to 2.88MB ASKIR Fast Ethernet Controller with MII Interface - x1 3. 34-Pin floppy Disk Drive Cable Audio Subsystem via AC-Link - x1 2. 40-Pin UDMA-100 IDE Cable Blue to motherboard, Gray to Master and Black to Slave Expansion Slots - 1. Motherboard Supports 10/100Mbps fast Ethernet with external VIA VT6103 PHY 1 2 x1 4. User’s Guide x1 5. Driver CD x1 Chapter 1 1-3 9VJL3 Motherboard Diagram Chapter 1 1-4 9VJL3 Motherboard Layout Page 7 Page 9 Page 6 Page 10 Page 11 Page 7 Page 10 Page 11 Page 9 Page 10 Page 9,10 Page 11 Page 10,11 Page 10 3 4 Page 8 Page 9 Chapter 2 Chapter 2 By turning on your system’s power. Enable the CMOS Setup Utility by pressing the Chapter 2 Hardware Setup delete key when your BIOS identification screen appears, then go to the Frequency/ If your motherboard has already been installed in your computer you may still need Voltage control option and select your CPU clock ration and CPU clock speed to refer to this chapter if you plan to upgrade your system's hardware. (please refer to Chapter3 for more details). You do not need to make voltage settings because this board will automatically This motherboard is electrostatic sensitive. Do not touch without set your CPU voltage. wearing proper safety gadget and make sure to disconnect the power cable from the power source before performing any work on your 2-3 Main Memory Configuration The DDR DRAM memory system consists two banks and can support the memory motherboard. Not doing so may result in electrical shock! size up to 1 GB per DIMM. If you only use one bank it does not matter which one 2-1 Installing a CPU Processor for Socket 478 The Intel® Socket 478, designed for the Pentium 4 processor, has been incorporated you use and if you use two or more banks, it does not matter which bank you install first. as a standard motherboard specification. To insert your CPU into Socket 478 please follow the steps bellow: 1. Locate the 478-pin CPU socket on the motherboard. 2. Unlock the socket by pressing the leaver sideways, and then open it up to a DRAM Specifications DIMM type: 2.5V, unbuffered 184 pin 64/128/265/512-bit DDR DRAM. 90-degree angle. 3. Locate a Gold Mark on the top surface of the CPU, which is close to one of the Module size: Single/double-sided 64/128/256/512 Mbytes or 1GB. CPU corners. The same corner will also be cut off, leaving a noticeable notch in Parity: Ether parity or non-parity. the CPU's corner. These markings indicate Pin 1 on the CPU. 4. Gently insert the CPU with Gold Mark/Pin 1 at the same corner of Socket 478, 2-4 Connector and Jumper Reference Chart which is located close to the end of the lever. Allow the weight of the CPU to Jump Connector push itself into place. Do not apply extra pressure as doing so may result in damaging your CPU. 5. When the CPU is correctly inserted, close the leaver with your finger on to of the Function Page PW 1/2 ATX Power Supply Connector 7 CN1A Front Panel (Power / Rest / SPK…etc.) Connector 8 FDD1 Floppy Connector 9 IDE 1 / 2 IDE Hard-Disk Connector 9 Installing a standard Intel® specified heat sink with cooling fan is JP1 CMOS Clear Jumper 9 necessary for proper heat dissipation from your CPU. Failing to install JP6 Disable/Enable USB 0/1 Device Wake-Up Jumper 9 these items may result in overheating and possible burn-out of your CPU. JP23 Green LED Mode Jumper 10 CPU to make sure the CPU is properly embedded into the socket. 6. Insert an appropriate heat sink and fan for proper Heat dispatch. 2-2 Setting Your CPU’s Performance Frequency Configuration: This motherboard uses a new user-friendly technology that enables the user to setup a main board’s CPU parameters through an easy to use BIOS setup procedure. It is no longer necessary to make many jumper settings as on conventional motherboard. After installing all your hardware into your PC system, you can manually configure FAN1 / 2 / 3 CPU/ System Cooling Fan Connector (12V) 10 CN2 / 2A CD-ROM Audio-in Connector 10 CN3 Auxiliary Audio-in Connector CN5 / 5A Wake on LAN / Modem Connector CN23 / 23A Front USB Connector 11 CN24 Front Audio Connector 11 IR1 IR Connector 11 your CPU clock ratio and CPU clock according to your processor’s specifications. 5 10 10,11 6 Chapter 2 Chapter 2 2-5 Connector and Jumper Settings Connectors are used to link the system board with other parts of the system, normal state. Then the keyboard or USB connector can function properly again. including the power supply, the keyboard, and the various controllers on the front user wasted time and inconvenience. Unlike conventional fuses, the poly-fuse does not have to be replaced, relieving the panel of the system case. CN1A (Front Panel Connector) 1. PWR-SW (Over-ride Power Button Connector) The power supply connector is the last connection to be made while The power button on the ATX chassis can be used as a installing a motherboard. Before connecting the power supply, please normal power switch as well as a device to activate make sure it is not connected to the power source. Advanced Power Management Suspend mode. This mode is used for saving electricity when the computer is All cables that provided by CHAINTECH come with a security-proof. not in use for long periods of time. The Soft-OFF by PW 1 / 2 (ATX Power Supply Connector) The power cord leading from the system's power supply to the PWR-BTTN function in BIOS's Power Management Setup menu must be set to [Delay 4 Sec.] to activate this function. external power source must be the very last part connected when When the Soft-OFF by PWR-BTTN function is enabled, pushing the power button assembling a system. The ATX power supply provides a single rapidly will switch the system to Suspend mode. Any occurrence of external 20-pin connector interface, which incorporates standard +/-5V, activities such as pressing a key on the keyboard or moving the mouse will bring +/-12V, optional 3.3V and Soft-power signals. The Soft power the system back to Full-On. Pushing the button while in Full-On mode for more signal, a 5V trickle supply is continuously supplied when AC than [4 seconds] will switch the system completely off. See Over-ride Power power is available. When the system is in the Soft-Off mode, Button Operation diagram. this trickle supply maintains the system in its minimum power 2. P-LED (Power LED Connector) state. The power indicator LED shows the system's power status. It is important to pay The ATX 12V power supply has a new +12V (4-pin) and attention to the correct cables and pin orientation (i.e., not to reverse the order of +5V/3.3V (6-pin) auxiliary power connector. To enable the these two connectors.) delivery of more +12 VDC and +5/3.3V VDC current to the 3. G-BTN/G-LED (Green Button Switch/LED Connector) motherboard. Some ATX cases provide a Green button switch, which is used to put the system in Power-On By Modem While in Soft-Off state, if an external modem ring-up signal occurs, the system Suspend mode. In Suspend mode, the power supply to the system is reduced to a trickle, the CPU clock is stopped, and the CPU core is in its minimum power state. wakes up and can be remotely accessed. You may enable this function in BIOS's The system is woken up whenever the keyboard or mouse is touched. The system Power Management Setup menu. (See section 3. 5) resumes in different ways as defined by Power Management Setup screen in BIOS. Blinking LED in Suspend Mode While in Suspend mode, the LED light on the front panel of your computer will 4. RESET (System Reset Switch Connector) This connector should be connected to the reset switch on the front panel of the flash. Suspend mode is entered by pressing the Override Power Button, pushing the system case. The reset switch allows you to restart the system without turning the Green button on your ATX case, or enabling the Power Management and Suspend power off. Mode options in BIOS's Power Management menu. (See section 3.5) 5. SPEAKER (Speaker Connector) Poly-fuse Over Current Protection The poly-fuse protects the system from dangerous voltages that the system might be This 4-pin connector connects to the case-mounted speaker. 6. HD-LED (IDE Activity LED Connector) exposed to via the keyboard or USB connector. In case of such exposure, the The IDE activity LED lights up whenever the system reads/writes to the IDE poly-fuse will immediately be disconnected from the circuit, just like a normal fuse. devices. After being disconnected for a certain period of time, the poly-fuse will return to its 7 8 Chapter 2 Chapter 2 FDD1 (Floppy Connector) JP23 (Green LED Mode Jumper) This cap is to setup Green LED flash mode. (Optional) Pin Definition The motherboard provides a standard floppy disk drive connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types, use this connector to connect 34 pins of Floppy. 1-2 Normal (default) 2-3 Reserve FAN1/FAN2/FAN3 (CPU/System/Case Cooling Fan Connectors) The board's management extension hardware is able to IDE 1/2 (IDE Hard-Disk Connector) The motherboard has a 32-bit Enhanced PCI IDE and detect the CPU and system fan speed in rpm Ultra ATA66/100 controller that provides PIO mode vary depending on the manufacturer. On standard fans, (revolutions per minute). The wiring and plug may 0~4, Bus Master, and Ultra ATA66/100 function. This the red is positive (+12V), the black is ground, and the connector is used for connecting 40 pins of ATAPI yellow wire is the rotation signal. Connect the devices. case-cooling fan to FAN3. The wiring and plug may IDE 1 only connects two IDE devices. (Primary Master/Slave) vary depending on the manufacturer. On standard fans, the red wire is positive (+12V) and the black wire is ground. IDE 2 only connects two IDE devices. (Secondary Master/Slave) CN2/CN2A (CD-ROM Audio-in Connector) Use the audio cable enclosed with your CD-ROM disk JP1 (CMOS Clear Jumper) There is a CMOS RAM on board that has a power Pin Definition supply from external battery to keep the data and 1-2 Normal (default) system configuration. To clear the contents of the 2-3 Clear CMOS Data CMOS, please follow the steps below. drive to connect the CD-ROM to your motherboard. This will enable your CD-ROM's audio function. CN3 (Auxiliary Audio-in Connector) (Optional) This connector is for Auxiliary Audio-in Device. 1. Disconnect the system power supply from the power source. 2. Set the jumper cap at location [2-3] for <5 seconds>, and then set it back to the default position. CN5 [WOL (Wake-on-LAN) Connector] Enable the Wake Up On LAN selection in BIOS's 3. Connect the system's power and then start the system. 4. Enter BIOS's CMOS Setup Utility and choose Load Setup Defaults. Type [Y] and Power Management Menu to use this function. The then press [Enter] to continue. capability to remotely manage PCs on a network is a 5. Set the system configuration in the Standard CMOS Setup menu. significant factor in reducing administrative and JP6 (Enable/Disable USB 0/1 Device Wake-Up Jumper) A USB keyboard hot key or a USB mouse click can Pin Definition woke up this board. To use this function, select a hot 1-2 Disable (default) key of your choice at the USB Resume from S3 option 2-3 Enable under Wake Up Events in the BIOS's Power On ownership costs. Magic Packet technology is designed to give WOL capability to LAN controller. This header is used to connect an add-in NIC (Network Interface Card) which gives WOL capability to the motherboard. Management screen. You must also set this jumper's cap to pins 2-3 to use this
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks